IPF5000 MANUAL PDF

View and Download Canon ImagePROGRAF iPF Series service manual online. ImagePROGRAF iPF Series Printer pdf manual download. View and Download Canon ImagePROGRAF iPF brochure & specs online. Large-Format Printer. ImagePROGRAF iPF Printer pdf manual download. and free pdf instructions. Find the office and computer equipment manual you need at ManualsOnline. Canon IPF Printer User Manual. Page 1. Page 2.

Author: Vugal Gozshura
Country: Bolivia
Language: English (Spanish)
Genre: Travel
Published (Last): 1 December 2012
Pages: 26
PDF File Size: 6.11 Mb
ePub File Size: 2.40 Mb
ISBN: 314-8-42624-249-6
Downloads: 4589
Price: Free* [*Free Regsitration Required]
Uploader: Vobar

Choose Yes to cut the roll at the current lpf5000. Other Precautions Chapter 1 1. Print quality from all three will be the same, but the smaller size printer adds a cassette feed which is missing in its larger siblings. F 6 While pressing down the protrusion[A], slide the spur unit[1] in the direction of the majual to remove it.

Basic Operation Outline Chapter 2 2. Locating and Installing Your Download When your download is complete please use the instructions below to begin the installation of your download or locate your downloaded files on your computer. The paper supplied from the cassette is checked for normal feeding using the sensors provided along the paper feed path.

Table of Contents Add to my manuals Add. Chapter 4 1 Remove the cutter unit. The purge motor is used for manyal. Chapter 3 23 Open the package and take out the ink tank by holding its knobs. Paper Path Chapter 2 2. Shadow detail is very good, although not as deep as the HP Z shows.

Installation Chapter 3 3. The ink passage consists of an ink tank, a carriage unit having a printhead, a purge unit.

Canon IPF5000 Printer User Manual

Adjustment And Setup Items Chapter 4 4. Transporting The Printer Chapter 3 3. Vent holes This printer has four vent holes, [1] to [4].

F b Removing the roll feed unit 1 When removing the roll motor, remove the roll feed unit[2] from the main body, and then remove the right cover[3] by removing the two screws[1]. Scan Wait Time 1 sec. Printer Stats Transition Chapter 1 1.

Page 65 Chapter 2 menu, the pinch roller unit moves up to allow you to feed paper from the front of the printer according to the message shown on if5000 operation panel. Chapter 3 3 Grasaping the carrying handles[1] on the left and right side of the bottom,place the printer on a level place such as a table. If the Printhead malfunction is not covered by this Limited Warranty or the applicable warranty period has expired or has not been sufficiently established by appropriate documentation, you will be charged for a replacement Print Head at the then current cost established by Canon.

TOP Related Posts  KRYGOWSKA GEOMETRIA PDF

CANON IMAGEPROGRAF IPF BROCHURE & SPECS Pdf Download.

Details Of Service Mode Chapter 7 7. Chapter 3 F 9 With Basket Wire 2 [1] positioned so that the bend faces forward, insert it in the hole of the Basket Table [2] from below.

Be careful to avoid back strain and other injuries. F e Left rear cover Removing the left rear cover 1 When removing the left rear cover[2],open the top cover, and then remove the left circle cover, tank cover, and ip5000 rear cover. Graphic Matte Canvas, 17″ Roll This pH neutral polyester blend canvas has a bright white, matte finish surface. Ink mist that mabual inside the printer and ink splashes from the media are collected ipf000 the filter through the front duct and the air flow path inside the printer by the driving of the mist fan, thus preventing mist from discharged outside ,anual printer.

Lift cam sensor This is a photo-interrupter-type sensor. Chapter 4 b Points to Note on disassembly and Reassembly of Carriage Unit 1 Align the mark on the gear[3] with the mark on the bushing[4].

Canon imagePROGRAF iPF5000

To prevent foreign matter from entering the ink port, installed the unpacked ink tank in the printer immediately. Head Management Sensor Chapter 4 F 9 Remove the four screws[1] and one joint[3], and then remove the two ink tank unit F[2]. Page 20 Chapter 1 Twisted-pair shielded cable, 5. The printer wakes from the Sleep mode when the user presses any button on the operation panel or data is received from the host computer.

Chapter 2 Fan filter Mist fan F During operation of the suction fan, suspended substances are collected in the filter through the airflow path inside the printer, preventing them from being emitted to outside of the printer. You must call the appropriate number below for remote diagnostic assistance for operation and support of the Product:.

TOP Related Posts  O PRINCIPE EO MENDIGO PDF

Next, move the carriage[2] onto the platen. Printer Mechanical System Chapter 2 2.

Page Chapter 4 PG Approx. Warranty replacement shall not extend the warranty period of the defective Product. Mwnual Menu Settings Main menu items are described in the following tables. Page 55 Chapter 2 Carriage lockpin Pump cam sensor Glycerin tank Sub cap Purge motor Pump encoder F b Wiper unit The wiper unit operated by the purge motor wipes the print head face.

Page Chapter 4 F 3 Place the scale[5] on the mist mnaual as shown below, adjust the wire guide height so that the wire roller[6] touches the top surface of the scale, and then tighten the screw loosened in step 1. Chapter 4 F c Left cover Removing the left cover 1 When removing the left cover[3], remove the left circle cover, open the top cover, and then remove the tank cover.

Align the mark on the lift gear[1] with the mark on the gear[2] to remove the ring[5]. Got it, continue to print. Yes” is selected in the printer driver when roll media is used, the cutter unit mounted in front of the spur unit automatically cuts the roll media.

When the link that operates in conjunction with the valve cam shields light, this sensor detects that the ink supply valve has been opened. Chapter 3 F 22 Before unpacking the ink tank you want to install,shake it slowly times.

Canon iPF Review – PhotographyBLOG

Cutter Unit Chapter 2 feed roller shaft eject roller shaft drive belt spur cam sensor spur motor spur unit F 2. Paper detection sensor This is a photo-interrupter-type sensor. Next, remove the cushioning materials by raising the left and right sides of the printer one maanual another with your hand inserted in the clearance as indicated in the figure [1].