FURUNO LS 4100 MANUAL PDF

Marine manuals and free pdf instructions. Find the marine product manual you need at ManualsOnline. Furuno Ls Fish Finder User Manual. Page 1. Ls – read user manual online or download in PDF format. Pages in total: en este manual. Asi mismo, FURUNO apreciaría cualquier suge- rencia o comentario en relación con el equipo. Características. La FURUNO LS es una.

Author: JoJom Zulur
Country: Egypt
Language: English (Spanish)
Genre: Music
Published (Last): 9 April 2011
Pages: 29
PDF File Size: 9.29 Mb
ePub File Size: 15.83 Mb
ISBN: 303-3-88808-969-9
Downloads: 17407
Price: Free* [*Free Regsitration Required]
Uploader: Faera

Page 36 Transom hole: When the power is reappliedafter turning off the equipment withminimum brilliance, minimum brilliancewill be set after the equipment goesthrough its initial start up. Therefore, whenconnecting eternal equipment havingpositive ground, do not ground thesignal line to the chassis. Mount the sensor close to the centerline of the boat. The transmission speed for both input and output is bps. Therefore, the 50 kHz frequency is useful for general detection and judging bottom condition.

Transom Mount Transducer Construction of fairing block 3. Choose the water type with which to use the LS, from Salt or Fresh. Contact yourdealer for connection ofother equipment. Only qualified personnel should workinside the equipment. When choosing a location keep the following in mind: Comments to this Manuals Your Name.

Furuno Ls4100 Fish Finder User Manual

Press the [MARK] key again. Don’t show me this message again. Below is the basic menu operating procedure.

TOP Related Posts  PRACTICAL CHESS ENDINGS BY PAUL KERES DOWNLOAD

This may require a certain amount of experimentation for fine tuning at high cruising speeds. If a hole has been drilled in thetransom, open the appropriate slot inthe transom cable cover.

Selects basic display range. Fire or electrical shock can result if thepower is left on. Adjust the brilliance asnecessary. Position the second cable clamp halfway between the first clamp and the cable hole. If you cannot restorenormal operation, contact your dealerfor advice.

Furuno LS-4100 Fishfinder

Sandpaper Silicone sealant Silicone grease Remarks on installation Requires appropriate nav data. Only qualified personnel should work inside the equipment. Carefully remove anymarine life with a piece of wood orfine-grade sandpaper. The display unit can be installed on adesktop, on the bulkhead or flushmounted in a panel.

Turn key beep on or off. Table of Contents Add to my manuals Add. For any NG, request service. Repeat step 1 to ensure that the angle of the sensor is correct. Fill the gap between the wedge front of the transducer and transom with epoxy material to eliminate any air spaces. Automatic function permits unattended adjustment of range and gain. Therefore, the 50 kHzfrequency is useful for general detectionand judging bottom condition. Fill the gap between the wedge frontof the transducer and transom withepoxy material to eliminate any airspaces.

TOP Related Posts  UL1111 PDF

Your manual failed to upload Performance will be affected. Set range of each of the eight basic Setting windows other thanthose on menus are erased if there isno operation within about sevenseconds. Menu Operating Procedure 1. Page 31 submerged, even when the boat isrolling, pitching or up on a plane athigh speed.

Mounting locationTo ensure the best performance, thesensor must be submerged inaeration-free and turbulence-free water. MENU from page 2 on the menu. For any NG,request service. Electronic chart display and information system pages.

Coat with silicone sealant. Maneuvering the vessel in this conditionmay result in a manuxl situation. A special connector is required to test the NMEA port.

5″ LCD SOUNDER LS | Fish Finder | Products | FURUNO

Use the specified power cable. The installer of the equipment is solely responsible for the proper installation of the equipment. Construction of manjal block3. Page 36 Transom hole: The signal line ground is isolated fromthe chassis ground, however the powerline is not insulated. This mode is useful for determining bottom contour.